20 Inch Length Futura Concealed Undermount PUSH to Open Soft and Silent Full Extension

Product Discontinuation AlertThis item has left our catalog. It's either upgraded to a newer model, didn't meet our high customer satisfaction standards, or the manufacturer said goodbye. But don't worry, CabinetParts is always here with top-notch alternatives.


All the product info you could ask for...

  • Size Info

  • Slide Length : 20 Inch
  • Drawer Box Length : 19-5/16 Inch
  • Manufacturer Info

  • Manufacturer : Salice
  • Manufacturer Part # : 421.23.650
  • Other Important Info

  • Finish : Zinc-plated
  • Load bearing capacity : Per pair: (50 lbs.) 22.68 kg
  • Material : Steel
  • Model series : A6558 Futura Push with Soft Close Frameless Mounted
  • Supplied with : 1 Pair of drawer runners1 Pair of snap-in couplings
  • Type of closing : with self closing mechanism
  • Manufacturer Resources

Our customers say Salice products...

  3.9 out of 5
based on 9 ratings

"These reviews are from our customers who have purchased Salice products."
  • 2 of 3 people found the following review helpful
    2 of 5 Quality control is slipping... August 6th, 2026
    by Nicholas from Acworth, GA

    I purchased 6 pairs of 15" Progressa+ drawer slides for a walnut dresser. Of the 12 slides, 5 were assembled incorrectly at the factory. This review page does not support attaching pictures, but basically the geared mechanism was assembled incorectly. On the 5 bad slides, the gears were off from 1/4" to over 1/2". The intended use was for inset drawers, and it's not feasable to have one side of the drawer to be 1/4" to 1/2" shorter than the other. I was able to disassemble the slide, re-align the internals and re-attach the geared slider to bring the slides into correct position using a 'good' slide as a reference. The quality of the slides is actually very good, just the assembly in the factory was bad. More troubling is that I've reported this on the Salice customer feedback site over a week ago, and have not had any response at all.

    This review is about similar Salice Drawer Slides. (SH-G5U6S381XXF6)

    Was this review helpful? yes no

  • 0 of 1 people found the following review helpful
    3 of 5 Not needed in my project August 12th, 2026
    by Robert from TREMONTON, UT

    I ordered some of these, just in case, but did not need them for my project. They apparently provide a hole for the rear hook on a shelf that is too thin to drill the hole in the shelf. These come singly, so if you need them, order two for each pair of drawer slides.

    This review is about similar Salice Drawer Slides. (SH-A8825650000)

    Was this review helpful? yes no

  • 4 of 5 Simple under-drawer slide clips August 12th, 2026
    by Robert from TREMONTON, UT

    These are simple, only allowing adjustment for the drawer height. They come in a pair (left & right) to match a pair of the drawer slides.

    This review is about similar Salice Drawer Slides. (SH-421.23.000)

    Was this review helpful? yes no

  • 5 of 5 Great slide for my application August 12th, 2026
    by Robert from TREMONTON, UT

    These slides work great for my application, where I had an oddly shaped drawer and had to mount one of the slides a few inches in from the edge of the drawer. The slides were fairly easy to install, they work smoothly, and allow full extension of the drawers.

    This review is about similar Salice Drawer Slides. (SH-A65559/60)

    Was this review helpful? yes no

  • 5 of 5 mounting bracket June 22nd, 2026
    by kenneth from Olympia, WA

    (no comment given)

    This review is about similar Salice Drawer Slides. (SH-433.17.000)

    Was this review helpful? yes no

See More Reviews

Reviews about us...

  • 4 of 5 | September 28th, 2026

    I love the heft and look of the bronze plates. My only concern is with the mounting screws. For such a large plate and for security matters the screws are only 1/2 inch long. They would be easy to pry off. I have bought 1 inch screws, (the longest that wo

  • 4 of 5 | September 27th, 2026

    we had significant difficulty deciphering the measurements needed. Cabinet parts develop drawings to illustrate the needed dimensions.

  • 5 of 5 | September 27th, 2026

    And fast shipping . Thank you!

  • 5 of 5 | September 26th, 2026

    I’ve been looking for these parts and you delivered! Thanks

  • 5 of 5 | September 26th, 2026

    These are very sturdy legs. I am using them as center supports for my latex mattress. They are easy to adjust and I feel confident they will last as long as the mattress. Delivery was prompt. I used another brand of support legs but they did not work out.

See More Reviews
×